Who Owns Your Injection Mold? Ownership, Storage, and Transfer Before You Pay for Tooling

Flat illustration of an injection mold with a metal ownership plate attached and a document with a checklist beside it.

You paid for the mold. The invoice is in your files, the tool is running, and the parts are shipping. Then the relationship changes — a price dispute, a quality problem, a decision to move production — and you ask for the mold back. That is when many buyers discover the question they never settled: paying for a mold is not the same as owning it.

You own a mold you paid for only when a signed agreement says the factory holds it on your behalf. A paid invoice proves you paid; it does not say what you bought, who holds it, or when you can take it. Get the ownership, storage, and release terms in writing before the deposit — not when you need the mold back.

This guide explains what the law does when nothing is written down, how the way you pay for tooling changes what you can claim, what the agreement must say, and the seven steps of moving a mold to another factory.

Why paying for a mold is not the same as owning it

An injection mold is movable property, and it never leaves the factory that built it. That combination is the whole problem. Under China’s Civil Code, ownership of movable property passes on delivery — but a mold you paid for is never delivered to you; it stays in the factory’s press, running your orders. As the Importivity guide to mold ownership in China explains, four articles of the Civil Code explain most mold disputes:

  • Article 224: ownership of movable property passes on delivery, unless the law says otherwise. A mold that never leaves the factory was never delivered to you.
  • Article 447: a creditor may keep a debtor’s movable property that is already in its lawful possession when a debt is due. If your company owes the factory money, the factory has a legal basis to hold the mold.
  • Article 448: between two companies, the property held does not have to relate to the debt. An unpaid production invoice can be the reason a mold you paid for in full is held back.
  • Article 783: under the contract for the mold work itself, a factory that has not been paid may keep the finished work or refuse to hand it over, unless the parties agreed otherwise.

Put together, the risk is plain: a mold paid for in full can still be held over an unrelated unpaid invoice. The same code also gives you the fix. Article 228 says that when the parties agree the party transferring an item keeps possession of it, ownership passes when that agreement takes effect — which is exactly the case of a mold that never leaves the factory. Article 449 lets the parties agree that property may not be held under a lien. Article 784 makes the factory liable for loss or damage to work it keeps for you through poor care. Article 785 bars a contractor from keeping copies or technical data without permission.

None of this helps unless it is written down. A quotation line that says "mold fee" proves you paid. It does not say what you bought, who holds it, or when you can take it. That is why the ownership terms belong in the agreement signed before the deposit — and why a factory’s willingness to sign them is part of choosing a plastic mold manufacturer. A supplier that will not put ownership in writing is telling you something about the relationship, not about the tool.

One caution before going further: this article explains what the cited guides say about the law. It is not legal advice, and it is not a substitute for it. Have a qualified lawyer review your own agreement before you sign it — a lawyer who knows the jurisdiction that will actually govern your contract.

Paid, amortized, or factory-owned — how payment decides ownership

How you pay for tooling decides what you can claim later. Quotes often mix these arrangements without naming them, so ask which one you are being offered before you pay anything. The table below is adapted from the Importivity guide, restated in our own words:

How the tooling is paidWho owns it if nothing is writtenWhat to write down
Paid up front by youUnclear. The invoice proves payment, not ownership, and the mold never leaves the factoryYou own each listed tool from the final tooling payment, the factory holds it for you, and it may not be held against any claim
Amortized into the unit priceThe factory, at least until the agreed quantity has shippedThe quantity after which ownership passes to you, and a buyout figure for the unrecovered balance if you leave early
Fee refunded after a volume targetUnclear. You paid, but a refund promise says nothing about who holds titleThat the refund does not change ownership, and what happens to the tool if you leave before the target
The factory’s own mold (catalog or ODM product)The factory. You are buying its productExclusivity for any change made to your design, such as a logo insert or a new colour
Your insert in the factory’s mold baseSplit, and easy to disputeEach insert listed by number as your property, and how it will be removed and handed over

Amortized tooling is a reasonable deal for a new product. It lowers your cash outlay and keeps the factory invested in your reorders. The cost is control: until the tooling is paid off, moving production means paying the rest first. Put the starting tooling figure and the amount recovered per unit in the agreement, and ask for the per-unit tooling charge to appear as its own line on every invoice. Then the remaining balance is a calculation, not an argument.

The insert row deserves attention because it is the easiest to overlook. Many buyers pay for a custom insert that sits in the factory’s standard mold base, and assume the whole tool is theirs. If the agreement does not list each insert by number as your property, the split between your insert and the factory’s base becomes an argument at the moment you most need it settled.

What the mold ownership agreement must say

A tooling agreement can be two pages. Make it a separate document, or a schedule to your supply agreement, signed and stamped with the factory’s company chop, with a Chinese version that governs if the factory is in China. Most of its clauses point at something you or an inspector can check on the mold itself. Work through this checklist before the deposit:

ClauseWhat it must settle
Asset listOne row per tool: mold number, part name and number, cavity count, steel grade for the cavity and core, mold base size, weight, hot or cold runner, the date it was finished, the price paid, and photos. Add the mold design files as a deliverable
Ownership and possessionYou own each listed tool from the date of the final tooling payment, and the factory holds it on your behalf at no charge. This is the Article 228 arrangement in plain words
No lien and no set-offThe factory may not hold the molds against any claim, including an unpaid production invoice. Money disputes get settled separately
Owner plateYour company name and the mold number on a metal plate riveted to the mold base, or engraved into it. Cavity numbers molded into every part, so a part found in the market can be traced to a cavity
LocationThe address where the molds are kept. No moving them to another plant or to a subcontractor without your written consent
Use only for your ordersNo parts for other buyers, no copies of the mold, and no keeping your design data after the relationship ends. Article 785 already bars a contractor from keeping copies or technical data without permission; restate it
Shot lifeA guaranteed number of shots, with repair or replacement at the factory’s cost if the mold fails sooner under normal use
MaintenanceRoutine maintenance at the factory’s cost, a written maintenance log, and a shot counter reading sent with every order
ReleaseOn written notice, the factory hands over the molds within a fixed number of days, packed for export, for a handling fee agreed now. The drawings and spare parts go with them, and so do the last-shot samples
No scrappingThe factory may not scrap, sell, or modify a mold without your written consent, however long the gap between orders

The owner plate does not create ownership on its own. It lets an inspector match the steel in the press to the asset list you both signed. The asset list is the document that matters: without a signed list naming each tool, the plate is a label on a disputed object.

Two clauses buyers most often skip are the location clause and the no-scrapping clause. A mold moved to a subcontractor’s plant without your knowledge is a mold you cannot inspect, and a mold scrapped after a long gap between orders is a mold you would have to pay to build again. Both are cheap to write and expensive to discover.

What the law says when nothing is written

The China position above is the one that matters most for a mold built and stored in Shenzhen. But the pattern — a default rule that a written agreement overrides — exists in other jurisdictions too, and it is worth understanding as a pattern rather than as a single law.

Illinois is one example. The Illinois Dies and Molds Ownership Transfer Act of 1997 (765 ILCS 1053) says that if a customer does not take possession of its die, mold, form, jig, tooling, or pattern from a fabricator within three years of the last use, the customer’s rights, title, and interest transfer to the fabricator for destruction (Section 10). Before that happens, the fabricator must give written notice by registered mail (Section 15), and the customer has 90 days to respond or take possession, or the title vests in the fabricator (Section 20). A written agreement between the fabricator and the customer is not affected by the Act (Section 30).

Here is the nuance that matters, and the reason Illinois is only an example. Section 25 of the same Act says it does not apply to a die, mold, or form for the manufacture of plastic products — a separate Plastics Dies and Molds Ownership Transfer Act applies to those. So the 1997 Act is not the law governing a plastic injection mold in Illinois. What it shows is the pattern: several US states have dies-and-molds laws, the default varies by jurisdiction, and in every case a written agreement overrides the default. Read the official Illinois statute text to see how the sections fit together — and then have your lawyer check the law of the jurisdiction that actually governs your contract.

The practical conclusion is the same in every jurisdiction: the default is whatever the law says when you wrote nothing, and the default is rarely what a buyer would choose. The agreement is what replaces it.

How long should a mold last, and who keeps it running

Ownership is worth little if the mold wears out before its time and nobody agreed who pays for the repair. The SPI classes, set by the Society of the Plastics Industry (now the Plastics Industry Association), give both sides a shared vocabulary for how long an injection mold should last. As summarized in Fictiv’s guide to tooling life, cited in the Importivity guide:

SPI classBuilt for
Class 101One million cycles or more
Class 102Medium to high volume, up to one million cycles
Class 103Under 500,000 cycles
Class 104Under 100,000 cycles
Class 105Prototype tooling, under 500 cycles

Name the class in the asset list. It tells the factory what standard of steel and build you paid for, and it gives you a yardstick when it later says the mold is worn out. A Class 101 mold that fails at 200,000 cycles is a different conversation from a Class 104 mold that fails at the same count — but only if the class was written down at the start.

The shot counter is the cheapest audit tool you have. It is a counter mounted on the mold that adds one for every cycle. Ask for a photo of it with each order, then compare it with your own numbers: shots multiplied by cavities should roughly equal the parts you were invoiced for, plus setup and scrap. A counter running far ahead of your orders means the mold is making parts for someone else. Our mold-life article explains the shot counter and the maintenance log in more detail, including the preventive-maintenance intervals and the records to keep at each service.

Split maintenance costs into three buckets in the agreement. Routine cleaning, polishing, and lubrication belong to the factory as part of the unit price. Wear parts such as ejector pins and springs are the factory’s cost within the guaranteed shot life. Refurbishment, or a replacement mold after the guaranteed life, is yours — quoted in advance. This split is the commercial side of the maintenance schedule; the schedule itself, and what to inspect at each interval, is covered in the mold-life article linked above.

Where the mold is stored, and how you know it is still yours

A mold in storage is a mold you cannot see. The agreement should make it visible:

  • One stated address. The location clause names the plant where the mold is kept. Any move — to another plant, to a subcontractor, to a warehouse — needs your written consent first.
  • Access on reasonable notice. You, or an inspector you appoint, can see the mold, photograph the owner plate, and read the shot counter. A factory that refuses a visit is a factory whose storage you cannot verify.
  • Preservation between runs. Cleaning, rust prevention, and proper storage are part of routine maintenance, not an extra. A mold left unprotected between orders corrodes, and corrosion is a repair bill that arrives with the next order.
  • A storage record. The maintenance log should show when the mold last ran, when it was cleaned and preserved, and its current condition. Ask for the log with each order, alongside the shot counter reading.
  • Insurance and liability. Article 784 makes the factory liable for loss or damage to work it keeps for you through poor care. State in the agreement who carries the insurance for the stored tool and what happens if it is damaged by fire, flood, or mishandling.

Storage is also where the ownership question meets the customs question. If the mold is yours and it sits in China, it is still an asset you own abroad — and that has consequences for how you declare it, which the next section covers.

Tooling money is part of your customs value

US Customs counts tooling in the value of the goods it helps make. Under 19 CFR 152.102, a mold you supply to the factory free of charge or at reduced cost is an "assist", and its value is added to the declared value of the imports. Money you pay the seller for a mold is generally treated as part of the price actually paid or payable — the total paid to the seller for the goods. Either way, the tooling money belongs in customs value. The Importivity guide explains the position; the regulation itself is the source to check with your broker.

The regulation also tells you how to spread the value. Section 152.103(e) lets you apportion it over the first shipment, over the units produced up to the first shipment, or over the entire anticipated production — or by another method that follows generally accepted accounting principles. Pick one, tell your customs broker before the first entry, and keep the tooling invoices. If you supply a mold you have already used to a new factory, the regulation values it at its original cost adjusted down for that earlier use.

This matters for ownership because the customs value of the assist is evidence of what you paid for and what you supplied. Keep the tooling invoices with the asset list: the same documents that prove ownership also support the customs declaration.

How to move a mold to another factory

Moving a mold goes smoothly when the paperwork was finished before the relationship cooled. The order of steps matters, because each one depends on the one before it. This seven-step sequence follows the Importivity guide:

  1. Settle every open invoice first, or agree in writing how the balance will be handled. Any unpaid amount gives the old factory grounds to hold the tool.
  2. Send a written release request that cites the agreement and the asset list, and get a release letter back stamped with the factory’s chop, naming the molds and the handover date.
  3. Order last-shot samples — parts from the final run before the mold comes out of the press. They show how the tool performed before it moved.
  4. Get a condition report with photos of the cavity and core surfaces, the shot counter reading, and a list of worn or damaged parts. Have an inspector witness it if the relationship is tense.
  5. Collect the support material: mold drawings, spare inserts and pins, and the process sheet that records the settings the mold ran at, such as melt temperature and cycle time.
  6. Crate and export. Coat the steel against rust, crate it, and let your forwarder handle the export paperwork, since the mold leaves as cargo with its own declaration.
  7. Run a trial at the new factory. Confirm its press fits the mold — clamp tonnage, platen size, tie-bar spacing — then approve trial parts against your golden sample before placing a volume order.

The last-shot samples and the condition report give the new factory a baseline, so a problem at the trial run can be traced to the move or to the mold itself. The release letter is the step that stalls most often: without a signed agreement, there is no letter to ask for, and the move becomes a negotiation rather than a procedure.

One distinction to keep clear: this is the move of a mold that has been running production at the supplier’s plant. Buying a mold to run in your own factory is the opposite case — the buyer-plant purchase, where machine fit and acceptance evidence are settled before the build. Our export-mold guide covers that purchase, including the press-data sheet and the handover package that must arrive with the crate. Do not confuse the two: a mold that stays at the supplier’s plant needs an ownership agreement; a mold that ships to your plant needs a compatibility check.

The handover list: what the agreement must deliver

The ownership agreement and the tool-documentation handover overlap, and the agreement should name the handover as a deliverable. Our mold-maker guide sets out the handover list in full: approved 3D and 2D mold files, revisions, component identification, purchased-part references, cooling and electrical diagrams, trial records, inspection reports, spare parts, maintenance instructions, and open issues. Agree that list before machining starts, and confirm which CAD files are native, which are neutral exports, and which revision cut steel.

The handover matters for ownership because a mold without its drawings is a mold you cannot repair, copy, or run elsewhere. A buyer who owns the steel but not the design files owns half a tool. Keep a correction log linking each trial change to a sample, measurement, and approval, and keep the component identity tied to the tool drawing — so that when the mold moves, the records move with it.

Frequently asked questions

Can the factory sell my mold if I stop ordering?
Not if the agreement says otherwise. The no-scrapping clause bars the factory from scrapping, selling, or modifying a mold without your written consent, however long the gap between orders. Without that clause, the default in some jurisdictions lets title pass to the fabricator after a period of non-use — which is why the clause, and the written agreement behind it, matter more than any verbal assurance.

Does owning the mold mean I can take it at any time?
No. Ownership and release are two different things. The release clause sets the procedure: written notice, a fixed number of days, a handling fee agreed in advance, and the drawings and spares going with the tool. Open invoices should be settled first, or the factory may have grounds to hold it. Plan the move as a procedure with a date, not as a demand.

What if the mold was built before I asked for an agreement?
Ask for one now. A mold ownership agreement can be signed after the tool exists — list the tools, state the ownership and possession terms, and get the factory’s chop on it. It is harder to negotiate once the tool is running and the relationship is under strain, but a signed agreement after the fact is far better than none. Have your lawyer review it before signing, as with any agreement.

Who pays if the mold is damaged while it is stored?
It depends on the cause and the agreement. Under Article 784 of China’s Civil Code, the factory is liable for loss or damage to work it keeps for you through poor care. Routine maintenance and preservation are the factory’s cost; refurbishment after the guaranteed shot life is yours, quoted in advance. State the insurance position in the agreement rather than discovering it after the damage.

Send the part files and ask for the ownership terms before the deposit

The cheapest time to settle mold ownership is before the tooling deposit goes out. Send the inquiry through our contact page and include the STEP file, the 2D drawing with its revision, the resin grade, the annual volume and order quantities, who pays for the tooling and how, your storage and release expectations, the surface finish, and your target timing — and ask for the ownership terms to be stated in the quotation itself. The contact form has no secure file upload, so send CAD files by email after the initial reply.

A quotation that states who owns the mold, where it is stored, and how it is released is a quotation you can compare with another. A quotation that only says "mold fee" is a price for a tool you may not own.

Hey! I’m Jerry — a hands-on mold & CNC guy who’s spent years turning ideas into real, tangible products. From tight-tolerance molds to complex machining projects, I’ve seen (and solved) a bit of everything.

Beyond the tools and machines, I’m all about people: building trust, making things easier for clients, and finding smart solutions that work. I’ve worked with teams around the world, and I’m always excited to meet others who love creating and building as much as I do.

If you’re into manufacturing, product development, or just like a good behind-the-scenes look at how things get made — let’s connect!

Send Us Your Requirements

Let's review your mold project

Tell us what you’re building and we’ll help identify the right tooling path. Send your 2D drawing, 3D CAD file, resin, annual volume, tolerances, or target timeline when available.

Engineering-led reviewReply within one business dayConfidential project details

No obligation. We’ll review the information and reply with a practical next step. Prefer email? jerry@cavitymold.com.