Injection molding has grown to become a relatively versatile manufacturing technology. From the type of materials, the orientation of the injection, the power source to the mold type, you have a lot of decision making to do as a manufacturer. This can often seem overwhelming. So articles such as this and others we’ve published on the blog aim to help break down the different aspects of injection molding and inform your decision making. When it comes to choosing between single and multiple cavity molds, the decision has a direct impact on capital and the operating cost as well as the production output and profitability. While there are some specific products that could strictly limit you to single cavity molds, in most cases you have both options available to you as far as product design and performance goes. Most product categories don’t limit you to single-cavity or multi-cavity molds. So whether you are designing a product for medical, automotive, aerospace, consumer goods, sporting apparels or others, you almost always have the option of either. The question then comes down a lot to productivity and cost.
It might seem straightforward at first instance to go for as many cavities as possible for faster production. However as the article goes into more details on both types of mold we’ll delve into why the decision is not quite as simple as that.
The Single-Cavity Mold
A single cavity mold in injection molding refers to a mold that is designed to produce one part per cycle. A piece of metal with the impression of a product machined into it, usually in two halves in such a way that when it closes and plastic melt is filled into it and allowed to cool and solidify, the product is formed as one whole part.
The Multi-Cavity Mold
In the multicavity mold a mold piece is designed in such a way that it has two or more impressions of a product machined into it. It is designed to produce more than one part per cycle. When the mold is closed and filled with melt, upon cooling and opening several identical products get ejected from the mold at once. The primary goal of the multi cavity mold is to increase production output.
Comparing the two
Here we look at some factors to consider in deciding between single cavity and multi cavity molds. A table is included to serve as a decision map to assist you in choosing between the two based on your requirements.
Flexibility
Single cavity systems allow modifications to be made more easily. For multi-cavity molds, making a change to the design often means making changes to the entire mold set. This is because of the interconnectivity of the cavities and the need to balance the melt flow.
Although most systems will allow shutting off gates to cavities such that a single part can be made in one run where only one part is needed, the system parameters such as temperature and pressure must be modified for that cycle to prevent excessive filling pressure.
Production Output
Multi-cavity molds allow manufacturers to achieve more parts per cycle hence increased production output. The full advantage of this is reaped where the cycles occur seamlessly. Ejection for all multiple cavities occurs within the same cycle time as it would for a single cavity mold of the same product and the cooling is efficient such that the cooling of all the multiple cavities occur within the same time as it would take to cool a single cavity. This requires that the cooling channels are well designed to remove heat from each cavity as efficiently as it would be designed for a single cavity mold of the same product.
Many experts in the field state that the cycle time for single-cavity mold and multi-cavity mold are comparable but not always the same. This can be attributed to factors such as difference in surface area for heat exchange per part and other factors. Therefore for example when comparing the production output for a single-cavity mold to a multi-cavity mold with 10 cavities for the same product, the productivity does not simply increase by 10. It would be increased, but not necessarily in direct correlation with the number of cavities.
Design Complexity
Multicavity molds require more complex cooling channels and more sophisticated temperature control systems. Whereas in a single cavity mold the mold designer is only concerned with one mold cavity and the heat and melt flow into and out of that one mold, in a multicavity mold, this becomes a more complex interplay of parameters.
The melt is flowing from the injection unit into the clamping unit where the flow gets diverted into different cavities through the runners. This diversion introduces more uncertainties and more pressure and temperature variation. The pressure and flow of melt through the runners and gates and into the different cavities needs to be balanced to prevent filling problems or defects. This requires more complex calculations and implementation of more tools to monitor and control the flow and temperature parameters in the clamping unit. The challenge here is to ensure that all conditions are replicated across all the cavities to ensure the parts are identical and all equally cool within the same cycle time.
The inexperienced mold maker or operator will have a process that results in defects such as short shots (due to insufficient pressure), flash (due to excess pressure or wrong temperature settings), uneven shrinkage and dimensional inconsistencies in the parts that should be replicated (due to uneven cooling or pressure distribution). These problems are also likely to occur when using single-cavity molds if the mold maker or the operator is not sufficiently skilled, however the likelihood is amplified in multi-cavity molds.
Another factor to consider is that troubleshooting is more complex in multi-cavity mold systems due to just having increased uncertainties due to more cavities and more runners and gates. When a defect is detected, the problem might not even be from the cavity number where the part was ejected from. It could be anywhere else. Thus making troubleshooting more challenging.
Design of multi-cavity molds can be optimized using simulation software Automation is often introduced to improve efficiency and reduce defects and unexpected downtime
Cost
When directly compared, of course a multicavity mold would cost more than a single cavity mold of the same product. However when considering the design requirement for the multicavity mold and the fact that more product is to be produced from the multicavity mold, in the long run the cost per product is reduced for multicavity mold. In other words while the multi-cavity mold might incur higher capital cost, this is made up for through increased yield per cycle.
Because the same number of man hours is required to run both types of mold per cycle. A single cavity can incur lower cost with regards to paid time per part. On the other hand running a multicavity mold often requires operators with more complex skills who may demand/command higher wages. This should be put into consideration when comparing the cost of both.
Demand Fluctuation and Uncertainty Risk
For manufacturers operating in a market where the demand tends to vary within short periods, this poses a financial risk. Investing large capital in multi cavity molds mean you intend to mass produce a product in order to cut unit cost through large production. When the demand dips this presents the risk of having large inventory that sits in the warehouse. With single cavity mold, there is lower capital and operating cost at risk when demand dips. It would cost less to change the molds in order to switch production to a different product currently experiencing higher demand. Therefore a risk averse manufacturer might find single-cavity mold better suited.
Product Size
A larger part like large automotive parts and large equipment housings means that the injection molding machine is doing more work to process larger quantities of plastic melt to be injected into the mold. More cavities to be filled means more plastic raw material to be processed in the same machine. So before considering a multicavity system, you should consider the power rating of your injection molding machine. Another factor to consider is the space. Multi-cavity molds require more space on the production floor so be sure this is put into consideration.
Scraps and Regrind
How scraps are generated for single or multi cavity mold systems depends on the design of the specific mold. Single cavity molds can be designed with or without runners. With a good design, the total scrap from runners per product from multi cavity molds should be less than the runners required for a single cavity mold. This is because ideally you’d have one runner system feeding multiple cavities and this should be a balanced runner system.
Multiple cavities will always require runners. For a cold runner system, this means you will be generating more scraps per cycle. It also means a portion of the energy consumption, work done and wear on the machine will be going to generate scraps in the form of runners and sprue. Depending on the design this might be less per product when single cavity molds are used. Therefore while a single cavity mold can be designed without runners to significantly reduce the scrap generated per part molded, where runners are used it might result in more scrap per product compared to a multi cavity mold.
Indeed, many products allow for recycling where a percentage of scrap can be sent back to the feed as raw materials without having any noticeable effect on product quality or performance. However for many plastics, putting them through a second heating cycle reduces the mechanical properties of the plastics as a result of partial degradation. Therefore regrind might not always be an option.
| Choose Single Cavity if | Choose Multi Cavity if |
|---|---|
| Low volume production | High volume production |
| Prototyping, custom parts or test products | Mass production of identical parts |
| Very large parts like large equipment housings or furnitures | Smaller sized products like cups and tool handles |
| Lower capital budget | Higher capital budget |
| Product can command higher profit per piece to make up for higher unit cost | Profitability is tied to economics of scale so low unit cost is required |
| You need easy modifications and maintenance with less complicated operations | You have the capabilities and expertise to handle complex modifications and maintenance to achieve higher efficiency |
Conclusion
The single cavity mold offers simplicity and low budget start up but comes with higher unit cost and lower production output. While the multi cavity offers higher production output and efficiency at a higher capital, operational and maintenance budget.
Whether you go for single cavity mold or multi cavity mold depends a lot on your capital budget, production target, profit margin and product size. It is therefore up to you, the producer, to determine which of the factors discussed within this article is more important or to weigh the different factors together. Having professional advice from mold makers with experience working with clients from various parts of the plastic industry can help you make the best decision.
By Ololade Olatunji
24, August 2026
