You send a drawing to a CNC supplier. It says "smooth finish" on one surface and nothing on the rest. The parts come back, and now you are arguing about what "smooth" meant — while the delivery date slips.
Specify the finish as a number, a process, and a zone: an Ra value in micrometres (µm) for each functional surface, the named finish where one is needed, and the areas it applies to — plus a note on whether dimensions apply before or after finishing. The standard as-machined finish, Ra 3.2 µm, is enough for most non-functional surfaces; pay for tighter finishes only where function or appearance genuinely needs them.
This guide explains what Ra means, compares the common CNC finishes, shows how finishes change your dimensions, and gives you a callout checklist you can put on the drawing.
What Ra actually means
Ra — arithmetical mean roughness — is the standard way to put a number on surface texture. It measures the average deviation of the machined surface from an ideal flat plane, and it is normally expressed in micrometres (µm) on metric drawings. A lower Ra number means a smoother surface: Ra 3.2 µm is rougher than Ra 1.6 µm, which is rougher than Ra 0.8 µm, which is rougher than Ra 0.4 µm.
Two facts about Ra are easy to get wrong:
- Ra is a number, not a look. Two surfaces with the same Ra can look different — tool-mark direction, gloss, and grain all affect appearance. If appearance matters, specify the finish process and a visual reference as well as the Ra value.
- Ra measures texture, not size. A tolerance of ±0.01 mm controls a dimension; an Ra 0.8 µm requirement controls the texture of that dimension’s surface. You need both, and they are checked with different instruments.
Protolabs puts the scale in plain terms: the most widely used measure of surface roughness is Ra, and while a cast-iron frying pan sits near Ra 2,000 micro-inches, machined parts fall far below that — the question is how far below your part needs to go. See Protolabs’ guide to improving surface finish on machined parts.
What "as-machined" gives you
Every CNC part leaves the machine with a finish, whether you specify one or not. The standard as-machined finish shows minor visible tool marks that follow the cutting tool path. According to Hubs / Protolabs Network, the standard as-machined surface roughness is Ra 3.2 µm (125 µin), with tighter options of 1.6, 0.8, and 0.4 µm (63, 32, and 16 µin) available through additional finishing passes. See their guide to CNC machining surface finishes.
As-machined is the right default when:
- The surface is hidden inside an assembly.
- It carries no seal, no sliding contact, and no cosmetic requirement.
- The part is a functional prototype and speed matters more than appearance.
It is the wrong default when the surface seals, slides, mates with a bearing, or is the face your customer sees. Those surfaces need a deliberate choice — which is what the rest of this guide is for.
The common CNC finishes, compared
| Finish | Typical Ra | Best for | Watch out for | Relative cost |
|---|---|---|---|---|
| As-machined | 3.2 µm standard; 1.6 / 0.8 / 0.4 µm with extra passes | General surfaces, tightest dimensional tolerances, no added finishing cost | Visible tool marks; no corrosion protection | $ |
| Bead blasting | Matte texture; roughness not guaranteed | Uniform matte appearance, hiding tool marks | Manual process, so appearance depends on operator skill; can affect critical dimensions — mask holes and mating faces | $$ |
| Anodizing Type II (clear or colour) | Oxide layer 4–12 µm thick | Aluminium and titanium parts needing corrosion resistance and colour | Aluminium and titanium only; threaded holes need masking | $$$ |
| Anodizing Type III (hardcoat) | Oxide layer about 50 µm thick, up to 125 µm | Wear resistance, hard functional surfaces | The most expensive finish here; needs tighter process control | $$$$ |
| Powder coating | Coating 18–72 µm thick | Durable colour on any metal, high impact resistance | Less dimensional control than anodizing; hard to apply inside cavities | $$$ |
| Brushing / polishing | Down to Ra 0.4 µm and below with enough steps | Cosmetic metal faces, sealing faces, lower friction | Removes material, so it can change dimensions; cost rises with each step | $$–$$$$ |
The figures above come from the Hubs / Protolabs Network finishes guide and the Protolabs surface-finish guide, both linked in this article. Treat them as typical commercial values for quoting and comparison — your supplier should confirm what their process achieves on your material and geometry.
A few choices behind the table deserve a closer look:
- Bead blasting is an appearance finish, not a precision finish. It produces a uniform matte or satin surface and removes tool marks, but the final roughness is not guaranteed. Use it where the eye is the judge, not where a seal depends on the surface.
- Anodizing is not paint. It converts the surface of the metal itself into a hard ceramic oxide layer, which is why it protects against corrosion and wear and can be dyed. Type II is the decorative standard; Type III is the functional hardcoat, built with higher current density and a bath held near 0 °C.
- Powder coating is the flexible alternative when anodizing does not fit — for example on steel, or where a wide colour range and impact resistance matter more than tight dimensional control. It is cured in an oven at about 200 °C, so the part must survive that temperature.
How finishes change your dimensions
This is the part most drawings get wrong. Finishes do not only change how a surface looks — they change where the surface is:
- Anodizing grows in both directions. A 50 µm Type III coating extends about 25 µm above the original surface and removes about 25 µm below it. Hubs gives a concrete example: a cylinder 1.00 mm in diameter before anodizing measures about 1.05 mm after a 50 µm coating. If a bore must stay on size, mask it — or size it for the coating.
- Powder coating adds thickness. A typical 18–72 µm layer sits on top of the surface. Threaded holes and tight fits need masking or a post-coating allowance.
- Polishing and brushing remove material. Smoothing lowers Ra by taking metal away, which can move a dimension out of tolerance on a thin wall or a tight fit.
- Bead blasting mainly changes texture, but it can still matter on mating or sliding surfaces — mask what must stay precise.
The fix is a single sentence on the drawing: state whether dimensions apply before or after finishing. Then mask the features that must not change — threaded holes, bores, sealing faces, and electrical contact areas — and say so on the drawing. Our CNC machining guide covers tolerances, datums, and inspection in more depth; read it alongside this guide when you set the drawing up.
When is a tighter Ra worth paying for?
Tighter finishes cost money: extra machining passes, more steps, stricter quality control. Pay for them where the function demands it:
| Surface | Typical callout | Why |
|---|---|---|
| Hidden, non-functional faces | Ra 3.2 µm as-machined | Nothing to gain from smoother |
| General mating faces | Ra 1.6 µm | A common precision-machining finish; a good default for faces that meet |
| Sealing faces, bearing fits, sliding interfaces | Ra 0.8 µm | Friction, wear, and sealing depend on the surface |
| High-precision shafts, hydraulic faces | Ra 0.4 µm | Only where the function genuinely needs it — check the cost first |
| Visible cosmetic faces | Named finish (bead blast, anodize) + visual reference | Ra alone does not describe how a surface looks |
If you are unsure, ask your supplier what Ra their standard process delivers on your material, and specify tighter only on the surfaces that need it. A drawing that demands Ra 0.4 µm "all over" pays for precision on faces nobody will ever see. Our quality control and inspection page describes how surface-roughness measurement fits into first-article and in-process inspection.
The drawing-callout checklist
Before you send the drawing, check these seven items. A finish that is not written down cannot be quoted accurately, and cannot be inspected on arrival:
- Ra value per surface — a number in µm, not "smooth" or "fine finish".
- Lay direction — the direction of tool marks or grain, where it matters (for example, across a sealing face rather than along it).
- Zones — mark cosmetic faces, functional faces, and hidden faces separately; the same finish is rarely right for all three.
- Finish process by name — bead blast, anodize Type II or III, powder coat, polish — where a process is required, not just an Ra number.
- Masking — list the features to protect: threaded holes, bores, sealing faces, electrical contacts.
- Before or after finishing — state whether dimensions apply before or after the finish is applied.
- Reference standard — name the standard your Ra values follow (commonly ISO 21920 for surface texture or ASME B46.1), so the supplier measures the same thing you specified.
For molded plastic parts, the equivalent decision is the mold’s surface finish — a different subject, covered in our mold texture guide. Do not copy a mold SPI or VDI callout onto a machined-part drawing; the two systems describe different surfaces.
Frequently asked questions
Can I combine several finishes on one part?
Yes — it is common. Bead blasting before anodizing, for example, gives a uniform matte look plus corrosion resistance. Sequence and masking matter: agree the order with your supplier and mark the masked areas on the drawing.
My supplier offers "standard finish" — what does that mean?
Ask them to put a number on it. "Standard" usually means as-machined at about Ra 3.2 µm, but the only definition that counts is the one on your drawing. If their standard differs from your requirement, the drawing wins.
Does a smoother finish always cost more?
Almost always. Tighter Ra values need additional machining steps and stricter quality control, and secondary processes add handling, masking, and inspection. The cheapest finish that meets the function is the right specification.
Send a drawing your supplier can quote from
A finish specification is a buying decision, not a decoration. Send us your drawing with the finish callouts marked per surface, and we will quote against what is actually written there. Use our contact page and include the STEP file, the 2D drawing with Ra callouts and zones marked, the material, the quantities, the key tolerances, the finish required on each surface, and your target timing.

